Search results for: 'hand pipes'
- Related search terms
- hand
- hand 200 c3 all
- hand 200
- hand 20
- hand 200 c3 alle
-
Flush and fill unit DN 20consisting of:
Brass ball valve internal thread ¾",
with red butterfly handle,
with 2 fill and drain valves with hose connector 15 mm
565151, 565181, 565121, 565221: additionally with 2 cutting-ring compression fittings with support sleeve, premounted Learn MoreOur offer is exclusively aimed at corporate clients.
-
Flush and fill unit DN 25consisting of:
Brass ball valve internal thread 1",
with red butterfly handle,
with 2 outlets ½" before and after the ball,
2 self-sealing fill and drain valves with hose connector 15 mm
56431, 56441, 56451, 56461: additionally with 2 cutting-ring compression fittings with support sleeve, premounted Learn MoreOur offer is exclusively aimed at corporate clients.
-
Connection set DN 20Consisting of 2 adapter pieces with 1" nut and ¾" internal thread for connecting pipes with ¾" external thread under modular distribution manifolds DN 20 (¾")
Learn MoreOur offer is exclusively aimed at corporate clients.
-
Connection set DN 32Consisting of 2 insertion pieces for connection of pipes with 1¼" external thread below HeatBloC®s
Learn MoreOur offer is exclusively aimed at corporate clients.
-
Ball valvesTo shut off the lines during commissioning and maintenance.
Marked in colour for easy assignment, DVGW approved, connection side G¾" internal thread.
Including covering caps to avoid contamination of the ball valves until installation of the station.
The ball valves can be ordered with or without mounting rail.
When using the mounting rail, the ball valves are mounted to the wall even before the installation of the station. Thus all pipes can be connected and the system may be set under pressure. Learn MoreOur offer is exclusively aimed at corporate clients.
-
Stainless-steel corrugated hosesMaterial 1.4404
Minimum length 5 m per roll
more than 50 m per roll on request
When ordering by metre, please indicate: ... rolls with ... metres per roll Learn MoreOur offer is exclusively aimed at corporate clients.
-
Conversion kit from K31 to K32 DN 25-401x return pipe with check valve (200 mm wc, can be opened)
1x 3-way mixing valve
1x union nut
1x gasket
1x actuator with stop bolt and rotation lock
Learn MoreOur offer is exclusively aimed at corporate clients.
-
System separation DN 25 (1") for HeatBloC®sFunction:
Separation of the boiler circuit and the consumer circuit
Field of application:
for radiant panel heating systems with plastic pipes for the protection of new boilers in older heating installations
Recommended application range:
Min. residual head: 1.5 m
Temperature difference primary: 60-50 °C
Temperature difference secondary: 35-45 °C
Range of performance:
depending on the pump of the heating circuit used and the amount of plates of the heat exchanger
16 plates: up to 20 kW, 10 K up to 1720 l/h
30 plates: up to 23 kW, 10 K up to 2010 l/h
40 plates: up to 25 kW, 10 K up to 2150 l/h Learn MoreOur offer is exclusively aimed at corporate clients.
-
Piping group DN 20Piping group for hydraulic separator, consisting of 2 pipe sections, union nuts and gaskets, for connection of a vertically mounted hydraulic separator below a PAW distribution manifold.
Flat-sealing connection, completely insulated, outlet on the right or on the left.
Learn MoreOur offer is exclusively aimed at corporate clients.
-
Piping group DN 25Piping group for hydraulic separator, consisting of 2 pipe sections, union nuts and seals, for connection of a vertically mounted hydraulic separator below a PAW distribution manifold.
Flat-sealing connection, completely insulated, outlet on the left or on the right.
Learn MoreOur offer is exclusively aimed at corporate clients.